Visico 5 - Batteridrevet 400w studieflash med TTL og HHS sync op til 1/8000 sec



364,56 € ex. moms

422,89 €

inkl. MwSt.

3 års garanti
30 dages fuld returret
Professional Support
User Guide 
VISICO5 Studio flash 
Lithium battery powered system 
Wide output power adjustment 
Fast grab shots 
Stroboscopic flashes 
LED modeling lamp 
2.4G build-in FSK radio receiver 

Wireless power operation system 
7 f-stop power variability range from full to 1/16 
Adjustable Flash frequency reaches 20 times per second 
Adjustable successive shots reach 15 shots at max. 
Adjustable short flash duration from 1/1000 to 1/10000sec 
Adjustable 7 pre flashes 
13Ws energy saving LED modeling lamp 
Modeling light selective lighting time 5s, 10s, 15s, and 20s before auto shut off 
Build in 2.4GH radio receiver with16 channels 
Legible LCD readout 
Built-in replaceable Lithium battery 
AC power (100-240V) charging for worldwide use, and automobile 12V DC charger 

Table of Contents


Safety Notes 
Package Contents

 Preparing Your Flash for Use 
Mounting Flash Light 
Release Protective Cap 
Installing Reflector 
Installing Battery 

Charging Battery and Charging indicator 
Flash Light Controls 
Three Kinds of Menu Modes 
Flash Light Output Power 
FP High Speed Flashes 
Stroboscopic Flashes 
Triggering the Flash

 Test Button 
Sync Connection 

 Setting Preflashes 
Setting Preflashes Time Frame 
Setting Preflashes Block Time 

2.4G Build-in Radio Trigger 
Group function 
Operating the Modeling Lamp 
Audible Beep Setting 
Recycling Indicator 
Low Power Indicator 
Protection Features 

Low Power Protection 

Overheating Protection 
Installing Umbrella 
Changing Flash Tube 

Discharge the Flash Unit 
Remove Old Flash Tube 
Install New Flash Tube 

How to Care for Flash Capacitor 
How to Care for Lithium Battery 



Thank you very much for selecting VISICO5 Studio Flash. 
VISICO4 wireless studio flash is developed under the concept “free to shot”, integrating with 
operation system and power system in one unit, combining leading world high speed and 
stroboscopic technology, with 8 conventional breakthrough main features, using carefully selected 
components, adopting top of the line product configuration and humanized interface design. The 
studio flashes will meet your requirements for shooting in different conditions, and bring your 
with years of pleased photography experience. 
To make the best use of this product, please read product instruction completely before operation 
and keep it handy for your reference. 

Safety Notes 

Do not use the unit in an environment where moisture or flammable vapor is likely to come in 
contact with the unit. 
Do not explore any components in direct sun for a long time. 
Do not restrict air vents while in use. 
Do not use a unit with damaged covers, flash tubes, modeling lamps. If the unit is dropped or 
damaged in any way always have it checked out before using it. 
Do not place flammable materials close to either the flash tube or the modeling lamp when the 
unit is in use. 
Do not attempt to disassemble or service the unit on your own to avoid shock hazard. Only flash 
tubes and batteries may be replaced on your own. 
Do not drop foreign objectives inside the housing. There is a risk of electrical shock. 
Always use a blower brush or clean facial tissue to remove dust and moisture from the modeling 
lamp and the flash tube. 
Always turn off the unit whenever mounting or dismounting accessories. 
Always turn off the unit and remove battery before maintenance. 
Always keep out of reach of children. 
Package Contents 

Your VISICO 5 wireless stroboscopic studio flash should include the following items, please check 

1x VISICO5 studio flash 
1x Lithium battery (included in VISICO5 studio flash) 
1x LED modeling lamp (included in VISICO5 studio flash) 
1x 100-240V charger for Lithium battery 
1x Car charger adapter 
1x Standard reflector 
1x Protective cover 
1x Tripod head adapter 
1x 4m Sync Cord 

1/ Preparing Your Flash for Use 
1-1 Mounting Flash Light 

Select a light stand or support system of suitable weight and dimensions to ensure stable operation 
of the unit. Rotate knob clockwise to lock flash unit firmly on support system. 
VISICO4 studio flash includes a 1/4” Tripod head adapter. It is applied to fix on camera tripods or 
other support system with 1/4” screw. 

1-2 Release Protective Cap 

To remove protective cap, push the latch knob back towards the rear of the unit and rotate the 

reflector anti clockwise. Put the protective cap aside. 
CAUTION: To avoid deformation of plastic protective cap, always cool down flash unit before 
fitting protective cap. 

1-3 Installing Reflector 

Install the reflector where the protective cap was before. Align the three pegs on the reflector with 
the three slots, press the reflector in and rotate clockwise until it locks in place. 
Always switch off the unit before fitting and changing reflectors. 

Take care not to damage flash tube when fitting or removing reflectors or soft boxes. The flash 
tube is very delicate. 
CAUTION: Do not touch the lamp with your bare hands. Oil residue from your fingers can cause 
the surface of the lamp to heat unevenly and explode. Use white cotton gloves or a clean cloth. 

1-4 Installing Battery 

According to the battery shape, distinguish battery direction, and then put it into battery 
compartment case. Press the battery until hear a clicking sound when the battery is fully installed. 

Switch off power before remove battery. Press down lock catch on battery and take it out. 

CAUTION:Always switch off the unit and remove battery before replacing flash tubes or repair 
the unit. 

2/ Charging Battery and Charging indicator 

AC charge: Insert one end with 5.5mm plug into the charging socket on Lithium battery, and 
the other end of the charger into a grounded outlet.VISICO4 studio flash battery charger is 
developed for international use within the range of AC100-240V. A fully exhausted battery 
reaches full power after 5 hours’ charging. Depending on the battery condition, charging 
hours may change. 
.12V DC Outlet Charging: Insert one small end of car charger adapter into the charging socket 
of the battery. Plug the other end of the charger into to a vehicle’s 12V outlet. 
Note: Please remove plug from source supply after the battery is fully charged. 

.Charging Indicator: The 100-240V charger has a built-in charge indicator. The LED light is red 
while charging, and turns to green when fully charged. The charge will cut off charging 
intelligently after the battery is fully charged. 

3/ Flash Light Controls 

A LCD screen 
B Sync jack 
C Modeling lamp 
D Function button 
E Test button 
F Photocell 
G Beeper 
H Adjustment button 
I Power switch 

J Unbrella hole 

Sync jack 
Radio trigger signal indicator 

4/ Three Kinds of Menu Modes 

The studio flash contains the following three different menus: 

Switch on the unit, you will see the FIRST MENU with power output setting, flash duration 
setting, continuous flashes setting, and flash frequency setting. 
After press the function button( ) for 4 seconds,you will enter into the SECOND MENU 
with 2.4G radio trigger’s channel setting, preflash setting, group function, modeling lamp 
automatic extinguish delay time setting. 

After press the function button( ) for 8 seconds, you will enter into the THIRD MENU 
with preflash special settings. 
Note :The display will automatically quit from the second menu or third menu to the first menu if 
no button is pressed after 20 seconds, or press function button ( ) for 3 seconds. And settings 
are automatically stored. 

5/Flash Light Output Power 

The max. power output of the unit is 300Ws. Output power is variable over a 4 f-stops range (5 
f-stop points) from full to 1/16. It is represented by full stop increments:1/1,1/2,1/4,1/8,1/16. The 
power adjustment lists in the front page of the first menu. Press the adjustment ( )button will 
change the power. 


6/ FP High Speed Flashes 

The flash duration range is variable from F1 (1/1000s), F2 (1/2000s), F3 (1/3000s), F4 (1/4000s), 
F5 (1/5000s), F6 (1/6000), F7 (1/7000s), F8 (1/8000s), F9 (1/9000s) to FP (1/10000s). 
In the first menu, press function button( ),switch to the flash duration page “Fx”. Press 
adjustment button( ) to select proper flash duration. 
FP high speed flash is used to photographing a subject at nearer distance. It works together with a 
fast camera with a high frame rate to capture motion subject. 
Flash duration is 1/1000 in F1 mode…Flash duration is 1/10000 in FP mode 

7/ Stroboscopic Flashes 

According to one shutter signal, the unit will generate a series of fast flashes, so that there will 
be multiply images integrated in one picture. This function is good at photographing the 
trajectory of a moving object. 
Continuous flash numbers is variable from 3 times, 5 times, 7 times, 10 times, 12 times, and 
15 times. In the first menu, press function button( ),switch to “Multi x” page. Press 
adjustment button( ) to select proper continuous flash numbers. 
The flash frequency is variable from 1 flash/second (1Hz),3 flashes/ second (3Hz),5 flashes/ 
second (5Hz),10 flashes/ second (10Hz),15 flashes/ second (15Hz),20 flashes/ second 
(20Hz). In the first menu, press function button( ),you are at the frequency page when 
seeing blinking “FREQ”. Press adjustment button( ) to select proper frequency. 
.In order to ensure shooting effect,you may calculate the shutter speed that you need according 
to flash frequency. For example, when the display shows 10Hz, 15 Multi, then the shutter speed is 

8/ Triggering the Flash 
8-1 Test button 

The simplest way to trigger the flash is to press the TEST button. 

8-2 Sync Connection 

The sync jack on the flash may be used for direct connection to a sync cord or radio receiver. 

8-3 Photocell 

. Press the photocell button to turn “ON” or “OFF” photocell. 
The photocell is active when the “eye” symbol is displayed on screen. 
. The unit will be triggered when senses appropriate preflashes from master flashes or other 
nearby flash unit. This is a convenient way to wirelessly trigger your flash. 
. In order to enhance triggering accuracy and strengthen the ability of anti-jamming, the numbers 
of preflashes is able to be adjusted according to your demands in different photography occasions. 
It is variable from 0time, 1 time, 2 times, 3 times, 4 times, 5 times, 6 times, and 7 times. In “tx” 
mode, total operation time of preflashes is able to be set from 1 to 8 seconds. And in “bx” mode, 
the minimum time interval between two adjacent flashes can also be set. Default setting is t2, b5. 
8-3-1 Setting Preflashes 
In the second menu, the first page is Preflash setting “Cx”. “x” is the number of preflashes plus 
main flash from 1 to 7 times. Set the number of preflashes plus mainflash by pressing the 
adjustment button( ) 

Photo Cell "0" 
Circle with adjustment button( ) to “C0” automatic recognition mode . Use the camera –on 
flash and release a test exposure. The photocell detects the number of flashes the camera released 
and memorizes the value automatically. If no flash is detected during C0 mode, then the studio 
flash default to 1 preflash. 

Photo Cell "1" 
If you have selected "C1"in the procedure above, the unit will autoflash immediately when 
another flash is activated in the same area. 
Photo Cell "2" 
If you have selected "2" in "To Set the Photocell" above, the unit will autoflash on the second 
flash the photocell detects and will ignore the first preflash. 
Photo Cell "3" 
If you have selected "3", the unit will autoflash on the third flash detected by the photocell. 
Photo Cell "4" 
If you have selected "4", the unit will autoflash on the fourth flash detected by the photocell. 
Photo Cell "5" 
If you have selected "5", the unit will autoflash on the fifth flash detected by the photocell. 

Photo Cell "6" 
If you have selected "6", the unit will autoflash on the sixth flash detected by the photocell. 
Photo Cell "7" 
If you have selected "7", the unit will autoflash on the seventh flash detected by the photocell. 

8-3-2 Setting Preflashes Timeframe 

Press function button ( ) for 8 seconds, enter into the third menu. Total time of preflashes 
setting “tx” is in the front page of the third menu. “t” is the total time of all released preflashes 
plus mainflashes. It is variable from 1 second to 5 second, you can circle through pressing 
adjustment button( ). Default setting is “t2” (means 2 second). The flash light will only be 
triggered when all the preflashes are fired in your setting timeframe. Set the value “t” between 1-5 
to ensure all preflash plus the main flash are inside the time frame. 

Value t 1 2 3 4 5 

Time(second) 1 2 3 4 5 

8-3-3 Setting Preflashes Block Time 

In third menu, use the function key( ) to select “bx” page to set block time between two 
adjacent preflashes. Preflashes block time is to set the minimum delay between each preflash. Set 
value from1 to 9 by pressing adjustment button( 

). Default setting is b5. 
Value b 1 2 3 4 5 6 7 8 9 
Time (milisecond) 2 4 6 8 10 12 14 16 18 

8-4 The Photocell is located behind the red transparent cover on the top and at the back of the unit. 
The photocell is very sensitive but some experimentation with positioning may be necessary to 
ensure a reliable trigger, particularly if the cell is not in the direct line of sight of the triggering 
flash unit. Avoid directly illuminating the photocell from a continuous light source (such as ceiling 
lights or windows)since this can prevent correct operation. Very high ceilings can also affect the 
operation of the photocell. 

8-5 2.4G build-in Radio Trigger 

.The unit includes build-in 2.4G radio receiver with 16 optional channels. In the second menu, 
press function button( ) to “Ch x”page. Press adjustment ( ) button to set a proper 
VISICO 2.4G radio transmitter contains 16 independent channels. Studio flash is only 
triggered when transmitter and build-in receiver is at the same channel to trigger studio flash. 
. In order to avoid mutual interference, please assort different groups of radio receivers and 
transmitters with different channels. 
. The following pictures shows how to match code between radio transmitter and receiver 
(figure 1) 
8-6 Group Setting 

.In second menu, set channel of radio receiver “CH x” the same as radio trigger. The way to 
match code between radio transmitter and receiver correctly, please refer to figure 1. 

.Press function key( ) to the “Group x” page. There are four group codes (A, B, C, D) for 
selection. Press adjustment( ) key to select group. This group is corresponding to the A, B, C, D 
groups of radio trigger. 
.Press PB1 button to trigger studio flashes. 
.Press PB2 to reduce flash output power from 1/1---1/16 
.Press PB3 to increase flash output power from 1/16----1/1 
.Press PB4 to control modeling lamp ON/OFF 
9/ Operating the Modeling Lamp 

. The unit contains 13W LED modeling lamp. Press the modeling lamp button to turn the light 
‘ON’ and ‘OFF’. 
. To save the energy consumption, the modeling lamp isn’t on all the time. It automatically 
distinguishes after 5s, 10s, 15s, or 20s time delay. In the second menu, press function key ( ) to 
the “d x” page. Press adjustment key( ) to select proper modeling lamp delay time. 
Value t 1 2 3 4 

Delay time(second) 5 10 15 20 

10/ Audible Beep Setting 

You can turn audible beeper “ON” and “OFF” by pressing the AUDIO button. 
.The musical notes symbol will display on screen when the beeper is on, and will disappear 
when the beeper is off. 
When the beep is active, it will sound once the flash is recycled and ready to flash. 
11/ Recycling Indicator 

When studio flash is on charge, the charging status is indicated by a series of shaded bars. Once 
the flash is recycled, the numbers of shaded bars reach at maximum. When the beep is active, it 
will sound once the flash is recycled. 

12/Low Power Indicator 

Lower power indicator will only appear on screen when lithium battery voltage is lower than 8.6V. 
It is an indicator reminding end users to charge the battery as soon as possible. 

13/ Auto-dump 

AUTO-DUMP automatically discharges the capacitors when the power is reduced. Excess energy 
is automatically dumped when the flash power setting is reduced. Both increasing and decreasing 
the power setting generates heat inside the unit. Therefore avoid repetitive power setting changes. 

14/ Protection Features 
14-1 Low Power Protection 

Before battery power is exhausted, the studio flash will automatically make alarm, warning users 
to charge battery as soon as possible. If the users don’t charge in time, the flash light will cut off 
output power automatically when the battery is lower than 8.5V. Screen goes out at the same time. 

14-2 Overheating protection 

Continuous rapid firing of unit for extended periods of time may cause unit overheating, and trip 
the heat protection circuit. When the studio flash is overheating, it will automatically make alarm. 
When this happens, cool down the unit to a safe level and will start working normally again. 

15/ Installing Umbrella 

An umbrella with a handle diameter of 8 mm can be firmly secured in the umbrella holder. 
Firmly press the umbrella shaft through the holder, the locking knob is located on the side .Do not 
over tighten to avoid damaging the shaft of the umbrella. 
When the standard reflector is used, fit the umbrella in the hole of the reflector. 

16/ Changing Flash Tube 

16-1 Discharge the Flash Unit 
The charge in the flash unit must be discharged before removing the flash tube. To discharge the 
Flash unit: 

Make sure the Flash unit is ON. 
Push the red "TEST" button on the rear panel of the Flash. 
Immediately turn off the power switch on the rear panel of the Flash. Do not allow more than 
1/2 second between pressing the "TEST" button and turning the flash off. 
Remove battery from power source before removing the flash tube. It is recommended to wait 
at least 30 minutes before touching/removing the flash tube. 
Note: Use white cotton gloves or a clean cloth to prevent fingers from touching the flash tube. 

16-2 Remove Old Flash Tube 

First, remove the reflector. You will need to remove the retention spring wrapped around the top of 
the flash tube. With needle-nose pliers, unhook the retention spring loop. Grip the base of the flash 
tube on each side. Carefully pull the flash tube from the flash unit. 

16-3 Install New Flash Tube 

Make sure the power switch is off and the power cord is disconnected from the source. Locate the 
two flash tube pin sockets above the modeling lamp socket. Using white cotton gloves or a clean 
cloth, push the pins of the flash tube into the sockets using firm, even pressure at the base of the 
flash tube. With needle-nose pliers, hook the retention spring over the hook above the flash tube. 
Re-install the reflector. 
CAUTION:Always switch off the unit and remove battery before replacing flash tubes or repair 
the unit. 

17/ How to Care for Flash Capacitor 

One of the most important components of an electronic flash is the capacitor. Following the 
preventative maintenance below will increase the life and the reliability of your flash. 

If the unit is left unused for a few months or predominantly used at low power settings,it is 
recommended that the power be increased to maximum and the unit left switched on (modeling 
lamp OFF) occasionally for at least 30 minutes to help preserve the life of the capacitors. 

18/ How to Care for Lithium Battery 

Charging times and numbers of flashes may vary according to the condition of the battery. 
Charge the battery fully before using the unit for the first time. 
After you finished use the studio flash, or before you store the studio flash, switch off the 
If the battery stored for long time, it will become exhausted. Always charge every month. 
Do not drop the batteries onto hard surfaces, as this could expose the corrosive materials 
inside the battery case. 
Do not attempt to incinerate Lithium batteries or expose them to excessive heat. Batteries can 
explode if you toss them into a fire or place them near other extreme heat sources. 
19/ Specifications of Flash Lights 

Technical Dates 
Item number VISICO4 
Power output 300Ws 
Guide number GN(2m,Iso 100)1/60 
Reflector SF-610 
Output power rang Full power to 1/16 
Recycling time at Max.output power 2.5s 
Recycling time at Min.output power 0.4s 


Flash duration Full power 1/1 1/250s 
Flash duration Min. power 1/16 1/4000s 
Successive flashes 3shots;5shots;7shots;10shots;12shots;15shots 
Flash frequency 1Hz;3Hz;5Hz;10Hz;15Hz;20Hz 
Stroboscopic Mode Flash duration 
F1 1/1000s;F2 1/2000s;F3 1/3000s;F4 1/4000s;F5 1/5000s;F6 1/6000s; 
F7 1/7000s;F8 1/8000s;F9 1/9000s;FP 1/10000s; 
Modeling lamp LED 13W, 1370lumen (energy saving) 
Color temperature 5500K±200K 
Trigger voltage 5V Low voltage trigger 
Triggering frequency with inner 2.4GHz remote control, 100m effecitve distance in open air 
Trigger methods Sync cord;Photo cell;remote control;Test button 
Flash tube "Plug-in" tube (user replaceable) 
Flash light dimension diameter 125mm x length 220mm 
Flash light weight 1.8kg 
Number of flashes at full power per charge 700 shots 
Power source Lithium battery 
Battery capacity 6000mAH, 12V 
Charging way Battery plug-in charging type 
Charging voltage AC 100-240V, DC12V 
Charging time 5hrs 
Flash light protection Overheating protection; Low voltage automatic power cut-off system 
F3.5mm sync cord, standard reflector, protective cap, 100-240V charger, 
12V automobile charger, Tripod head adapter 

Charging time and number of flashes may vary according to the condition of the battery 

Flash frequency reaches 20 times per second: it means the interval time between two adjacent shots can reach 1/20 seconds. The point is the time speed between two adjacent shots.
Succesive shots reach 15 shots at max: it means the studio flash can shot 15 times at max per trigger. The point is the shot number per trigger.
The flash frequency depends on photographers demand when they shooting pictures.Flash requence 20 shots per second special used for shoot the object's trajectory.
5 f-stops between full and 1/16: as the VISICO 4 used is IGBT technology,if divide more f-stop,the color temperature deviation between each f-stops will be bigger,so finally we decide 5 f-stops 1/16
Our testing for VISICO 4,the battery full charged can shots 700
Produkt Blitz
Effekt 400W


Denne side bruger cookies for at forbedre din købsoplevelse. Læs mere her